Difference between revisions of "2010 Chevy Equinox"

From Hack Sphere Labs Wiki
Jump to: navigation, search
(→‎Misc)
Line 131: Line 131:
  
 
Bluetooth Mod:
 
Bluetooth Mod:
 +
*Has to do with a PCIM replacement (ACDelco 22797218 Multi Media Player Interface Module Assembly) that has extended functionality to support phone streaming.  One of the primary concerns of doing this is (besides if it will work) that will the radio need to be refreshed or something of that nature.
 +
*It looks like from this post (http://www.terrainforum.net/index.php?topic=2759.0) that a user stated:  No security code is needed, the radio is registered to the car's BCM.
 +
 
*http://www.equinoxforum.net/index.php?topic=4522.20
 
*http://www.equinoxforum.net/index.php?topic=4522.20
 +
  
 
Add Hard Drive:
 
Add Hard Drive:

Revision as of 02:08, 24 March 2013

My Posts


I broke the side mirrors and they have the heated glass you can buy OEM.

Bluetooth A2DP Mod

http://www.equinoxforum.net/index.php?topic=5839.0

http://www.terrainforum.net/index.php?topic=4522.0

http://www.amazon.com/ACDelco-22797218-Player-Interface-Assembly/dp/B0055B0QUS

http://www.terrainforum.net/index.php?topic=3769.msg50083#msg50083

Lockpick 2010 Equinox


Notes

GM BUS

Looks Like I have: 44-pin 29-bit GM LAN radio

Talking to some folks they call it: 29Bit v2

General Motors GMLAN

What is GMLAN? It is General Motors new Serial Communication Protocol that has been introduced in a couple of 2004 vehicles. These vehicles still use the Class2 protocol for engine management and will have a gate way between it and GMLAN. The next couple of years Class2 protocol will be replaced by GMLAN. The GMLAN is based off the Controller Area Network (CAN) protocol. GMLAN is a reliable and cost effective way to send data between different Electronic Control Units (ECU’s) in the vehicle.

GMLAN supports 3 different speed buses: 

   Low Speed - Uses Single Wire (refered to as Single Wire CAN or SWCAN). Used in security, doorlocks/windows and other low speed non-Real Time data.
   Mid Speed -
   High Speed - Uses Two Wire twisted pair. Primarily used for Powertrain and Chassis Devices as well as Anti Lock Brakes.


Let’s Chime In: GM 29 bit CAN Chime Control

For those of you who like to leave there car keys in the ignition while the driver door is open or who don’t where a seat belt, you’ve heard the Chime and have probably cursed it many, many times. Well I can help you defeat it or embrace it.

First you need to gear up. You will need to connect to the GM Single Wire CAN bus. This is on PIN 1 of the DLC (OBD II port). SW CAN runs at 33,333 bps (standard rate). So once you hooked up your device (see earlier posts for info on these), you should be able to communicate with the vehicle over SW CAN.

So now you just need to know the message, but first a crash course in GMLAN 29 bit ID.

The 29 bit ID is broken into three pieces. The Priority, Parameter ID, and Source Address. The priority is the first 3 bits of the ID. Priority allows for more important messages to get greater access to the network in the case of high network congestion. This leaves 26 bits reaming of the 29 bits. These are divided evenly amongst the Parameter ID and the Source Address (i.e. 13 bits each).

The Parameter ID is essentially the ID for what will be sent in the data portion of the frame. The Source Address is the node that sent the message. So messages from the address 040 all come from the same node. Cool huh!?

So let’s get to CHIME already…

Chime has a parameter ID of 0x0F. This means that if you want to send Chime you must put 0x0F starting at the 26th most signifigant bit. For example 0x1001E060 would be a chime command (0xF) with priority 4 (0 is highest priority) and send from node 0x60. Its easier to explain when we see this in binary. 0x0F is #b0:0000 0000:1111. So we put the whole ID together by taking the priority then parameter ID then source address. This will give us #b1:0000 0000:0001 1110:0000 0110:0000 (where the parameter ID is in bold).

Ok now that we’ve finished with the ID, let’s look at the data. The data portion is what is defining all of the characteristics of the Chime. In other words will this be a long chime or a short one, a click sound or a ding sound, a one-time sound or multiple times? There are 5 bytes that define all of these characteristics. So you will see that you can do a lot.

The first four bits of the first byte (the most signifigant nible) defines the speaker that this sound will come out of. For the front left speaker it is the most signifigant bit (or bit 7 of the byte). Next is the passenger (bit 6), then the rear driver side (bit 5), then rear passenger side (bit 4). So if you wanted to make the sound in only the driver speaker then you would send 0x8X in the first byte (where X is irrelivent).

The second nibble of the first byte describes the type of sound it will be. Either a beep or a click. Experiment to find out what these are.

The second byte describes the intonation of the chime. So you can adjust this on your own as well.

The third byte is the amound of repetitions you would like the sound to make. So if you want the chime to happen three times. This should be set to 3.

The fourth byte describes the duty of the chime. Experiment with this on your own.

Last byte is unknown currently. But if you know send me an email, I’ll update this entry.

So if you would like to send chimes to your car, here you go. If you want to cancel a chime, it should be good enough to have your software wait for a chime command and simply send one of its own with a really fast chime and a 0% duty cycle. That should end the last chime command.

Good luck and as always click on the contact link above if you have questions! Left Shift << 2

NU-GM3

  • The NU-GM3 is a Navigation Unlock integration interface that allows the factory Navigation & Bluetooth Features of your 44-pin 29-bit GM LAN radio to be used by the passenger at anytime.
  • Installed unit in vehicle. Unlocked DVD video while driving, address navigation/input is unlocked, etc. I did not hook up the unit to the backup DVD camera as I did not have the time to run the wire to power the reverse camera.
  • When you unlock the nav/vid/etc features while driving the software on the GPS thinks you are in park and the GPS does not update the navigation as fast, sometimes the car gps does not think that it is moving.

Lockpick Sites

Hard Drive

The hard drive is IDE and like the one pictured here: http://www.hgst.com/internal-drives/enterprise/endurastar/endurastar-j4k50

Misc

  • www.navigation.com/is-bin/INTERSHOP.enfinity/WFS/Navteq-NavteqNorthAmerica-Site/en_US/-/USD/ViewStandardCatalog-Browse?CatalogCategoryID=hlUKCghBzhoAAAE6OjZpoJOe&ShowAllProducts=YES

NAV UPDATE

22744758 - RADIO


  • Global A Radio

I read a site that stated that Global A was an connecting architecture and not the type of radio.


First, you do not have a color touch radio; they were not introduced until this year. What you have is what is called the High Feature Nav unit.


19212052

Pictures:

Bluetooth Mod:

  • Has to do with a PCIM replacement (ACDelco 22797218 Multi Media Player Interface Module Assembly) that has extended functionality to support phone streaming. One of the primary concerns of doing this is (besides if it will work) that will the radio need to be refreshed or something of that nature.
  • It looks like from this post (http://www.terrainforum.net/index.php?topic=2759.0) that a user stated: No security code is needed, the radio is registered to the car's BCM.


Add Hard Drive:

Steering Wheel Control Interface

Retrieved from "https://wiki.hackspherelabs.com/index.php?title=2010_Chevy_Equinox&oldid=1194"